ASTM F – Download as PDF File .pdf), Text File .txt) or read online. For testing threaded fasteners to ASTM F, we used an Industrial Series HDX frame equipped with spherically seated tension rods and standard bolt . ASTM F Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension.

Author: Tosar Kazrazuru
Country: Luxembourg
Language: English (Spanish)
Genre: Spiritual
Published (Last): 22 January 2016
Pages: 274
PDF File Size: 18.50 Mb
ePub File Size: 14.50 Mb
ISBN: 403-2-50188-940-2
Downloads: 6260
Price: Free* [*Free Regsitration Required]
Uploader: Fenrigal

Concrete, Asphalt and Rock. Stainless Steel and Nonferrous Washers.

As for internally threaded fasteners including nonheat- and heat-treated nuts, tests are provided for the determination of product hardness, proof load, and cone proof load. Aetm view current version of standard.

Section For Externally Threaded Fasteners: Historical Version s – view previous versions of standard. Test Method for Determining Decarburization and Carburization. Method 2, Yield Strength. These fixtures are specially designed for fastener, bolt and washer testing, and feature a key slot and recessed circular cutout that allowed us to quickly and correctly load the specimen. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application.

ASTM F606 Fastener/Bolt Testing

Tension Testing of Machined Test Specimens. Method 1, Length Measurement. Stainless Steel and Nonferrous Washers. Link to Active This link will always route to the current Active version of the standard. Check this box to receive pertinent commercial email from Instron focusing on products, upcoming events, and more!

  GARFIELD NAGARJUNA PDF

Method 2, Yield Strength.

Method 1, Length Measurement. In astmm instances where the testing requirements are unique or at variance with these standard procedures, the product standard shall specify the controlling testing requirements.

ASTM F Fastener Testing Bolt Test – Instron

Typically, property requirements and their applicable tests are specified in individual product standards, which are also complemented by ASTM F No other units of measurement are included in this standard.

It also provided the control necessary to perform the required proof tests, tensile tests, and combined proof and wedge tensile tests. Work Item s – proposed revisions of this standard. Subscribe to Our Newsletters. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

For Internally Threaded Fasteners: In the absence of any specified test requirement sthese test methods shall apply. Method 1, Length Measurement. Onsite Training At Your Facility. The values are stated in inch-pound for inch fasteners and SI metric units for metric fasteners. For Externally Threaded Fasteners: Tension Testing of Machined Test Specimens.

Test Method for Determining Decarburization and Carburization. If failure were to occur, toxic or flammable fluids or gases could easily result in fires, explosions or structural failures.

  FLUKE 700PD5 PDF

For externally threaded fasteners, the mechanical tests describe the procedures for determining the following properties: This abstract is a brief summary of the referenced standard. These test methods establishes the standard procedures for conducting tests to determine the mechanical properties of externally and internally threaded fasteners, washers and direct tension indicators, and rivets.

This device was specially designed for fasteners from Email addresses can only contain letters, numbers and the following special characters: E Clip On Axial Extensometer. Test for determining the surface and core hardnesses are, conversely, described for direct tension indicators, and through-hardened, carburized, stainless steel, and nonferrous washers. These rugged bolt holders were made from specialty steel and underwent a unique heat treating process making them able to withstand the violent recoil of fastener tensile failures.

Combining values from the two systems may result in non-conformance with the standard. For Washers and Direct Tension Indicators: And finally, product hardness testing is described for rivets.

Measures displacement for axial tensile, compression, and cyclic testing Gage lengths from 10 mm to 50 mm 0. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations adtm to use.