Question about Abit Fatal1ty AN8 SLi Motherboard . motherboard has user manual try to read it again, if you do not have manual then use a. Today, Rich Swinburne puts ABIT’s AN8-SLI motherboard through our battery of tests. Is it the Installation manuals, driver CD and floppy disk. ABIT hasn’t been on top form recently when it comes to Does this latest SLI motherboard mark a return to form for the enthusiast vendor? Installation manuals, drivers & utilities CD and floppy disks. ABIT AN8 32X.
|Published (Last):||11 March 2013|
|PDF File Size:||15.92 Mb|
|ePub File Size:||17.6 Mb|
|Price:||Free* [*Free Regsitration Required]|
Copyright and Warranty Notice The information in this document is subject to change without notice and does not represent a commitment on part of the vendor, who assumes no liability or responsibility for any errors that may appear in this manual. No warranty or representation, either expressed or implied, is made with manua,s to the quality, accuracy or fitness for any particular part of this document.
Connectors, Headers and Switches Install Realtek Audio Driver Hardware Setup Chapter 2. Hardware Setup Before the Installation: Failing to do so may cause the motherboard components or add-on cards to malfunction or damaged.
Always use the processor with the Heatsink and Fan Assembly installed. Do not touch the pins on the processor. On the other side, push the retention clip straight down to lock into the plastic lug on the retention frame.
Turn the cam lever to lock into the retention frame.
Abit AN8 SLI Manuals
This illustration is based on the model AN8 Ultra. Usually there is no hardware or BIOS setup requires after adding or removing memory modules, but you will have to clear the CMOS memory first if any memory module related problem occurs.
Chapter 2 Power off the computer and unplug the AC power cord before installing or removing memory modules. Locate the DIMM slot on the board. Hold two edges sbit the DIMM module carefully, keep away touching connectors.
Align the notch key mitherboard the module with the rib on the slot. Chapter 2 Please follow the instructions below to set the system ah8 SLI mode and install your graphics cards. Please handle the switchboard with caution. Watch out for the sharp edges.
Slightly push down the switchboard until the retention clip snap into places.
Make sure the switchboard is completely inserted into the slot. The system may be unstable without doing so.
Anit, 12, 23, and 24 should be left notherboard. These fan connectors are not jumpers. DO NOT place jumper caps on these connectors. Failing to do so may cause your system to work abnormally or malfunction. LED to not light, but a wrong connection of the switches could cause system malfunction. This header provides one additional IEEE port connection through an extension cable and bracket.
Pin shorted default: Hardware Setup 8. Connect the single end at the longer length of ribbon cable to the FDC1 on the board, the two connectors on the other end to the floppy disk drives connector. Connect the single end blue connector at the longer length of ribbon manuxls to the IDE port of this board, the other two ends gray and black connector at the shorter length of the ribbon cable to the connectors of your hard drives.
ABIT ANX nForce4 SLI x16 Motherboard Review –
This LED lights up when the power supply is connected with power source. This LED lights up when the system power is on. POST Code in address 80h to find out where the problem lies. Hardware Setup Remove the rubber protection-caps before using this optical fiber cable. Pull out the 3. Plug the end with 3.
ABIT Fatal1ty AN8 SLi, Socket , AMD Motherboard | eBay
This jack is used for either optical or line input. Plug one end of a standard 3. Please follow the below diagram to connect your sound system to the audio daughter card.
Remove the rubber protection-caps from both ends of the cable. Hardware Setup Analog connection for 5. Abi Panel Audio Connection Header This header provides the connection to audio connector at front panel. Bias Speaker Out Right Connects to Local Area Network. In order to increase system stability and performance, our engineering staffs are constantly improving the BIOS menu.
The BIOS setup screens and descriptions illustrated in this manual are for your reference only and may not completely match what you see on your screen.
You may switch between these two by clicking the left or right arrow key on keyboard: This item selects the external clock frequency. Due to the specification limit of the CPU you installed, the speed you set over its standard bus jotherboard is supported, but not guaranteed. This item displays the multiplier factor for the CPU you installed.
On The Fly F Exit These items display the power cycle statistics for each element. Chapter 3 Voltage Monitoring: Chapter 3 FanEQ1 Control: This item sets the high and low temperature limits desired for the fan speed control. This item displays the number of cylinders at which to change the write timing.
This item configures the number of sectors per track. BIOS Setup When this item is set to Enabled, if the BIOS detects no floppy drive, it will display a floppy disk drive error message. If this item is disabled, the BIOS will skip this test. This item selects the DRAM timing mode.
Three options are available: The default setting is Disabled. If you choose the wrong setting, the computer system will not run in a stable manner. This item selects which display slot to be initialized first when the system boots. When the system boots, it will first initialize PCI. When the system boots, it will first initialize PCIE. This option enables or disables the IEEE controller. You can set the Date month Alarm and Time Alarm hh: Any event occurring will awaken a system that has powered down.
This option enables or disables the AMD K8 cool and quiet function. Please disable this item while running under SLI mode. The installation procedures and screen shots in this section are based on the Windows XP operating system.
Choose [Yes, I want to restart my computer now. For those of other OS, please follow its on-screen instruction.
Abit AN8 SLI User Manual
The installation for USB 2. CD to enter the installation menu. The following screen appears. Click [Finish] to complete setup. Insert one blank floppy disk to the selected floppy drive and click [Build]. Check validity of RTC value: If CMOS checksum fails, use default value instead. Enable L2 cache 2. Start power on sequence 8. Enable ATX power supply 8. ATX power supply ready 8. DDR voltage ready 8. Yes, we highly recommend that you clear the CMOS before installing a new motherboard.
Please move the CMOS jumper from its default position to for a few seconds, and then back.
How can I get a quick response to my request for technical support? If you have a problem during operation, in order to help our technical support personnel quickly determine the problem with motherboarr motherboard and give you the answers you need, eliminate any peripheral that is not related to the problem, and indicate it on the form. Motherboard model number REV: Also please make sure you manualss the latest drivers from your peripheral card makers!
We are trying to expand and make the FAQs more helpful and information rich. Let us know if you have any suggestions.